How to crack a brinks 5059 safe

Brinks home security safe model model for in chesapeake va brinks safe manual model for in san jose ca. Brinks home security safe model for in henderson nv brinks safe model for in chesapeake va offerup brinks safe manual brinks home security safe model for in san jose ca. Related Posts Cowhide Sleeper Sofa.

Ryland Homes Tampa Fl. Mr Floor Carpets Bexhill. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Ryland Homes Tampa Fl. Mr Floor Carpets Bexhill. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish.

Accept Read More. Close Privacy Overview This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. Stop at 0 for example to park W1. Rotate the key and take note of where the pointer stops. Do the same with 2 or 2,5 increments for wheel 2, always leaving the other wheels at the same place, to have consistent readings.

Check the deepest gate, etc, etc, etc. If the wheels are unsimetrical or oval, it will get much harder. Note that I've never done this before. This is pure logic coming out of my head, based on my next to none knowledge in these locks. I'm hoping some of the old guys confirm or correct what I'm saying, both to help you with this, and to help me, as I'm going to be in front of a safe like that in a week or 2!

Here's an image for the pointer This was made using a pick because he had no key, but it's the same. Just use something longer to be easier to check the diferences. A bike spoke is perfect thin the tip for more precise readings You can also use a rubber band to have a constant pressure on it hold it to the handle or something so you wont have to be always rotating the key by hand, allowing for incorrect readings Hope this is of some help, and that someone corrects my crappy guide I can think of 4 people right now, so bear with me.

Planet Earth. The gate that obvious went in deeper would be the last wheel directly attached to the dial called the drive wheel or cam I would say. You could check that by turning both ways and see it hits the same spot on the dial when turned degrees right then left. That would be the last number in the combo. If you checked what that number was and isn't one of the 2 she remembers you are only 1 number away from getting it open.

But would have to determine which wheels those numbers she remembers are. Can mark how far the key is turned with that drive wheel lined up and try her numbers as the first and second number see if the key turns more etc.

Each time you try to find another gate or check her numbers return the drive wheel back to it's number then check how far the key turns. But since she got it new and can use the Brinks hot line to get the combo that is the way to go for sure. What a fun adventure! Have you been able to revisit it lately? Made any headway? About the only thing I would maybe suggest is starting the manipulation fresh with no assumptions. PhoneMan wrote She didn't remember what order the numbers were in she had 3 numbers out of four, and wasn't sure of 2 of them My cousin got the combo from Brinks, and it wasn't ANY of the numbers she had!

Go figure! Well, it was still a happy ending, and I'm still going to play with manipulation in my spare time. I'm a little late, but I have a similar model and details. The spindle turns the wheel furthest from the door which also functions as the drive cam.

It is significantly larger than the other wheels so while this is technically a 4-wheel lock it is functionally a standard 3-wheel. Because the distance from the punch to the gate varies on each side of each wheel these locks are probably set using a selection of pre-punched wheels at the factory. Strangely there is also a pin on the cam that changes the offset, perhaps a relic of a manufacturing change. This is one of the smoothest locks I've encountered since the spindle is essentially a 2-inch-long bearing and the fence is completely disengaged As for manipulation, the theory is to use a pointer on the key as fgarci03 described.