Huawei 3g bts pdf

EPS subrack 5. BBU 6. EMUA optional 7. PMU 8. Heater optional 9. SOU optional. Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel. Carousel Previous. Carousel Next. What is Scribd? Explore Ebooks. Bestsellers Editors' Picks All Ebooks. Explore Audiobooks. Bestsellers Editors' Picks All audiobooks. Explore Magazines. Editors' Picks All magazines. Explore Podcasts All podcasts.

Francisco Salvador Mondlane. Arthur Gouballe. More From Rashid Mahmood Sajid. Rashid Mahmood Sajid. Bilal Baig. Ehab Salah. Richard Alisangco. Jonathan Domingo. Popular in Radio Technology. Sukhada Deshpande. JC Adams. Ahmad Muzayyin. Victor Alberto Perez. Joe Muller. Kamil Ali Saiyed. Create one! Privacy Terms of use. Contact Us. If you need help, please click here:. Contact Us Enquiries. Technical Support. Login My Huawei Logout. Execute the following command to retrieve the ESN number.

Provide this ESN number to the commissioning team before going to the next step. Execute the following command to configure the Ethernet interface. Notify the commissioning team that the Ethernet interface is now configured. The commissioning team will enable the backhaul port on the site switch. This should show as enabled. Only perform these steps if requested by the commissioning team. Use the following commands. The RED highlight indicates information that must be provided by commissioning.

Execute the following steps: 1. The out put should look like the following. From this, you can determine whether a local software upgrade is needed. If so, proceed to section 9. If not running, start your local FTP server on your laptop. Note the username and password for your FTP server. Specify your FTP server, username, and password. Execute the command. Next, execute the following command to load the software the running area. Specify the new software label for the version.

The board LEDs can be used to monitor the activation status. Refer to section 5 for LED status descriptions. During activation, BMPT will reboot.

Outage time is approximately 5 minutes. When activation is complete, check the software version. The new software version should be listed in the main area. Next, check the bootrom version. The correct bootrom version should be displayed.

Slot No. The next sections will verify the operational status of the BTS. The active alarms should be displayed in the output area. The only acceptable alarm is Alarm of No User of Carriers.

There should be no other alarms. Each of these commands checks the fiber to the RRU. This will list the GPS state. GPS should be listed as the time source. This will list the operational state of each of the sectors. This is very important for network entry. This will list the R6 IP information and identifier as seen below. This will list all the neighbors configured for each sector. At a minimum, intracell neighbors should be configured.

The following example below shows a sure with intracell neighbors only. This will list all the handover triggers for each sector. Two trigger types should be configured for each sector as seen below. This will list the license configuration for all sectors and carriers. Ensure that all values are ON. This section explains the steps to perform these tasks.

Note: Sections Sections These values will be used to determine whether Wimax has introduced interference after the cut. Use the following steps to take these noisefloor readings. Telnet and log into the Expededience BTS. Execute the following command to clear the interference counters. Wait approximately 2 minutes and execute the following command to get new interference readings. The following steps must be executed in order to configure the hardware for a 3-sector BTS.

Execute the following MML command in the command input area to verify the software. The main area should show SPC or higher. Use the following command to check the status of the RRUs. A Normal status indicates that the RRUs are ready and you may proceed with the following steps. Access the Batch window by clicking the Batch link at the top of the window 8. Copy and paste the following commands into the command input area and execute.

The RED highlight indicates market specific information that must be provided. This can be ignored. This will list the current state of the carriers. If any carriers are blocked.